SMC AS系列速度控制閥的使用注意
1）安裝時，應事先將配管吹凈，應確認閥的流動反向沒有裝反。
2）接頭螺紋用手擰上后，用工具再旋2~3圈，安裝力矩要適當。
3）管接頭螺紋上，一般都已涂好密封劑，通常可使用2~3次。管螺紋如擰得過緊，密封劑會被擠出，應清除。
4）順時針旋轉調節手輪，節流閥是逐漸關閉的。使用時，應從全閉狀態逐漸打開，將氣缸調至要求的速度。
5）速度控制閥的調節圈數不得過給定值，以免損壞針閥。
6）萬向式速度控制閥，不宜用于經常回轉的情況
7）速度控制閥可能存在微漏，難于對氣缸進行低俗控制。同時，不得把速度控制閥當做截止閥使用。
8）應盡量靠近氣缸安裝，以控制性能，否則，響應時間過長，氣缸速度有可能難于控制。當氣缸至速度控制閥之間的配管容積大于氣缸容積時，就很難控制氣缸速度。也說明氣缸缸徑越小，速度控制越難
| AS1001F-01 | AS2201F-01-04S-X26 | AS2211FM-01-04 | AS3201F-03-08S | AS4201F-04-12N |
| AS1001F-01K | AS2201F-01-06 | AS2211FM-01-04S | AS3201F-03-08SD | AS4201F-04-12S |
| AS1001F-03 | AS2201F-01-06K | AS2211FM-01-06 | AS3201F-03-08SK | AS4201F-04-12SD |
| AS1001F-03K | AS2201F-01-06S | AS2211FM-01-06S | AS3201F-03-08SKN | AS4201F-04-12SK |
| AS1001F-04 | AS2201F01-06S | AS2211FM-01-08 | AS3201F-03-08SK-X264 | AS4201F-04-12SN |
| AS1001F-04-3 | AS2201F-01-06SD | AS2211FM-01-08S | AS3201F-03-08SN | AS4201F-04-12ST |
| AS1001F-04-3-X250 | AS2201F-01-06SK | AS2211FM-01-23 | AS3201F-03-08ST | AS4201F-04-12S-X214 |
| AS1001F-04-5-X250 | AS2201F-01-06SK-X264 | AS2211FM-02-04S | AS3201F-03-08S-X214 | AS4201F-04-12S-X95 |
| AS1001F-04D | AS2201F-01-06SN-X36 | AS2211FM-02-06 | AS3201F-03-08S-X214A | AS4201F-04-12W2 |
| AS1001F-04K | AS2201F-01-06ST | AS2211FM-02-06S | AS3201F-03-08S-X95 | AS4201F-04-13S |
| AS1001F-04N | AS2201F-01-06S-X214 | AS2211FM-02-08 | AS3201F-03-08W2 | AS4201F-04-13SK |
| AS1001F-04T | AS2201F-01-06S-X242 | AS2211FM-02-08S | AS3201F-03-09W | AS4201FE-04-10SK |
| AS1001F-06 | AS2201F-01-06S-X26 | AS2211FM-02-10 | AS3201F-03-10 | AS4201FE-04-12SK |
| AS1001F-06-3 | AS2201F-01-06S-X36 | AS2211FM-02-10S | AS3201F-03-10K | AS4201FG-04-10 |
| AS1001F-06-3-X214 | AS2201F-01-06S-X95 | AS2211F-N01-01S | AS3201F-03-10N | AS4201FG-04-10S |
| AS1001F-06D | AS2201F-01-06W2 | AS2211F-N01-07S | AS3201F-03-10S | AS4201FG-04-12 |
| AS1001F-06K | AS2201F-01-06-X36 | AS2211F-N02-08S | AS3201F-03-10SD | AS4201FG-04-12S |
| AS1001F-06N | AS2201F-01-06-X95 | AS2211FPG-01-06 | AS3201F-03-10SK | AS4201F-N04-10 |
